Power Tools reviews

4.6 out of 5 stars·5 reviews

Running electrical cables and plumbing pipes through walls is a fundamental part of any renovation or new build, and the neatness and speed of that work depends almost entirely on...

3.8 out of 5 stars·6 reviews

Modern electronics are packed onto circuit boards smaller than a credit card, with components so tiny that a stray sneeze could send them flying across the room. Repairing,...

4.3 out of 5 stars·5 reviews

Every tradesperson and serious DIYer has faced it: the screw or hole that is just out of reach. It sits behind a pipe, tucked inside a cabinet corner, or wedged between two joists...

3.7 out of 5 stars·6 reviews

Removing stubborn wheel nuts and seized suspension bolts is a job that tests both your patience and your physical strength. A long breaker bar works — eventually — but it is slow,...

4.1 out of 5 stars·5 reviews

Strong, invisible joints are the difference between furniture that lasts a generation and furniture that wobbles apart after two house moves. While traditional mortise-and-tenon...

3.4 out of 5 stars·6 reviews

Professional carpenters, kitchen fitters, and furniture makers know that not every routing job needs a full-size plunge router. For edge profiling, laminate trimming, hinge...

5.0 out of 5 stars·4 reviews

FEIN invented the oscillating power tool over 50 years ago, and in the decades since, their Multimaster system has set the standard for what a multi-tool should be. But even the...

5.0 out of 5 stars·4 reviews

Cutting metal on a construction site traditionally meant reaching for an angle grinder — effective, but also loud, spark-throwing, and prone to leaving a rough, burred edge that...

5.0 out of 5 stars·4 reviews

Some fasteners seem to have been installed by someone who believed they would never need to be removed again. The crank pulley bolt on a diesel engine, the rust-fused lug nuts on...

5.0 out of 5 stars·4 reviews

Repairing modern electronics means working with components that keep getting smaller. Surface-mount resistors no bigger than a grain of sand, multi-pin chips with legs spaced a...

3.9 out of 5 stars·5 reviews

When the holes get bigger and the concrete gets harder, there comes a point where a standard 800 or 900 watt rotary hammer starts to labour. Drilling 25 millimetre and larger...

5.0 out of 5 stars·4 reviews

In a professional cabinet shop or furniture factory, the difference between a finished panel that looks factory-perfect and one that looks obviously hand-trimmed often comes down...

3.7 out of 5 stars·5 reviews

Straight cuts are what circular saws and table saws do best — but the moment you need to cut a curve, a circle, or an intricate shape in wood, metal, or plastic, a jigsaw becomes...

4.7 out of 5 stars·4 reviews

Ingersoll-Rand is a name that resonates through every professional workshop, tyre bay, and heavy equipment depot in the world. For over a century, their pneumatic impact wrenches...

3.8 out of 5 stars·5 reviews

When you have invested time and money into your vehicle's appearance, keeping the paintwork looking its best requires more than a quick wash and a coat of wax. Swirl marks, fine...

4.7 out of 5 stars·4 reviews

For some trades, a hot air gun is not an occasional tool — it is a daily workhorse that runs for hours on end, often in dusty, demanding conditions. Professional floor layers...

4.7 out of 5 stars·4 reviews

When a hot air gun graduates from the occasional DIY tool drawer to a daily workhorse on construction sites, roofing jobs, and professional paint-stripping contracts, the demands...

3.7 out of 5 stars·5 reviews

When a surface-mount component fails on a circuit board, fixing it is not as simple as heating a couple of pins with a soldering iron. Modern electronics are packed with tiny SMD...

4.7 out of 5 stars·4 reviews

Not every fastening job happens within comfortable reach of a power socket or an air compressor. When you are working up on a roof, out in the garden, or deep inside a renovation...

3.6 out of 5 stars·5 reviews

Some tools are bought for a single project and then gather dust. An oscillating multi-tool tends to be the opposite — once you own one, you find yourself reaching for it...