Power, Garden & Hand Tools reviews

5.0 out of 5 stars·12 reviews

Drilling a 32 mm hole through reinforced concrete is where rotary hammer bits earn their keep or reveal their weaknesses. At this diameter, the bit is cutting through a large...

4.6 out of 5 stars·13 reviews

The difference between a good woodworking project and a great one often comes down to the quality of the final surface. No amount of careful joinery, precise measurements, or...

4.6 out of 5 stars·13 reviews

When you are anchoring structural steel, installing heavy machinery, or bolting down racking systems, a standard SDS-Plus bit will only get you so far. Once you need holes beyond...

4.3 out of 5 stars·14 reviews

Some jobs demand a tool that does not just get the work done — it dominates the material. When you are drilling 30 mm holes through reinforced concrete, breaking up old footings,...

5.0 out of 5 stars·12 reviews

In professional workshops, on construction sites, and in metal fabrication shops, the cordless drill faces demands that go far beyond driving screws into softwood. Drilling...

4.2 out of 5 stars·14 reviews

Cutting aluminium with the wrong saw blade is an exercise in frustration at best and dangerous at worst. A standard wood-cutting blade clogs almost instantly as the soft metal...

4.9 out of 5 stars·12 reviews

Driving nails by hand is one of those tasks that separates a quick job from an exhausting one. Whether you are fixing skirting boards, assembling timber framing, attaching...

4.9 out of 5 stars·12 reviews

Not every paint defect needs a full panel respray. A stone chip on the bonnet, a light scratch on the door from a car park mishap, a small scuff on a plastic bumper corner — these...

4.0 out of 5 stars·14 reviews

There is a moment every professional knows: you are halfway through a plunge cut into a solid oak door frame, the blade is buried to its full depth, and you feel the tool start to...

4.7 out of 5 stars·12 reviews

Working inside an engine bay, behind a dashboard, or within the tight confines of a vehicle's wheel arch presents a challenge that a standard straight drill simply cannot solve....

4.0 out of 5 stars·14 reviews

Pin nailers have long been the secret weapon of cabinetmakers and fine trim carpenters — driving headless 23-gauge pins that hold workpieces while glue dries, leaving holes so...

4.6 out of 5 stars·12 reviews

Some holes need to go deep. When you are anchoring into a concrete foundation that is half a metre thick, drilling through a retaining wall to install drainage, or setting long...

4.2 out of 5 stars·13 reviews

Standard oscillating multi-tools are brilliant at what they do, but they all share one frustrating limitation: the tool body is fixed in line with the blade, which means working...

4.5 out of 5 stars·12 reviews

Most holes drilled into masonry are shallow — 30 to 80 millimetres for a wall plug, an anchor bolt, or a pipe clip. But occasionally, a job demands a hole that passes all the way...

4.5 out of 5 stars·12 reviews

There comes a point in any serious paint correction or surface finishing project where a dual-action polisher simply is not aggressive enough. When you are dealing with heavy...

4.5 out of 5 stars·12 reviews

There are bolts that a standard drill-driver simply cannot touch, no matter how much you lean into it. The lug nuts on a car wheel that have been torqued to 120 Newton metres by a...

4.4 out of 5 stars·12 reviews

Whether you're cutting rebar on a construction site, grinding weld seams smooth in a metal fabrication shop, or slicing through paving slabs in a garden renovation, a powerful...

3.8 out of 5 stars·14 reviews

Not every drilling job calls for hammer action, brushless motors, or Bluetooth connectivity. Sometimes what you need is a straightforward rotary drill that spins a bit with enough...

3.5 out of 5 stars·15 reviews

Setting up for compressed air work for the first time can feel like a chicken-and-egg problem: you need tools to justify buying a compressor, but you need a compressor to use air...

4.6 out of 5 stars·11 reviews

Whether you are restoring a vintage piece of furniture, preparing a metal surface for painting, or putting the final polish on a woodworking project, the difference between a good...