DIY & Tools reviews

4.0 out of 5 stars·5 reviews

Damp, stale air is the silent enemy of every bathroom, kitchen, and utility room. Without proper ventilation, moisture from showers, baths, and cooking condenses on cold walls and...

5.0 out of 5 stars·4 reviews

FEIN invented the oscillating power tool over 50 years ago, and in the decades since, their Multimaster system has set the standard for what a multi-tool should be. But even the...

5.0 out of 5 stars·4 reviews

Cutting metal on a construction site traditionally meant reaching for an angle grinder — effective, but also loud, spark-throwing, and prone to leaving a rough, burred edge that...

5.0 out of 5 stars·4 reviews

Some fasteners seem to have been installed by someone who believed they would never need to be removed again. The crank pulley bolt on a diesel engine, the rust-fused lug nuts on...

5.0 out of 5 stars·4 reviews

Repairing modern electronics means working with components that keep getting smaller. Surface-mount resistors no bigger than a grain of sand, multi-pin chips with legs spaced a...

3.9 out of 5 stars·5 reviews

When the holes get bigger and the concrete gets harder, there comes a point where a standard 800 or 900 watt rotary hammer starts to labour. Drilling 25 millimetre and larger...

5.0 out of 5 stars·4 reviews

In a professional cabinet shop or furniture factory, the difference between a finished panel that looks factory-perfect and one that looks obviously hand-trimmed often comes down...

4.7 out of 5 stars·4 reviews

When you pick up an oscillating multi-tool, you are holding one of the most versatile power tools ever made. It can cut through wood, slice through metal, scrape off old adhesive,...

3.7 out of 5 stars·5 reviews

Straight cuts are what circular saws and table saws do best — but the moment you need to cut a curve, a circle, or an intricate shape in wood, metal, or plastic, a jigsaw becomes...

4.7 out of 5 stars·4 reviews

Ingersoll-Rand is a name that resonates through every professional workshop, tyre bay, and heavy equipment depot in the world. For over a century, their pneumatic impact wrenches...

3.2 out of 5 stars·6 reviews

For anyone who works with fabric, thin wood veneers, insulation, carpet underlay, or decorative panelling, a powered staple gun transforms a repetitive, hand-cramping task into...

3.8 out of 5 stars·5 reviews

When you have invested time and money into your vehicle's appearance, keeping the paintwork looking its best requires more than a quick wash and a coat of wax. Swirl marks, fine...

4.7 out of 5 stars·4 reviews

Whether you are renovating a room, tackling a plumbing repair, or simply trimming a door frame to fit, a standard set of tools can only get you so far. Tight corners, awkward...

4.7 out of 5 stars·4 reviews

For some trades, a hot air gun is not an occasional tool — it is a daily workhorse that runs for hours on end, often in dusty, demanding conditions. Professional floor layers...

4.7 out of 5 stars·4 reviews

When a hot air gun graduates from the occasional DIY tool drawer to a daily workhorse on construction sites, roofing jobs, and professional paint-stripping contracts, the demands...

3.7 out of 5 stars·5 reviews

When a surface-mount component fails on a circuit board, fixing it is not as simple as heating a couple of pins with a soldering iron. Modern electronics are packed with tiny SMD...

4.7 out of 5 stars·4 reviews

Not every fastening job happens within comfortable reach of a power socket or an air compressor. When you are working up on a roof, out in the garden, or deep inside a renovation...

3.6 out of 5 stars·5 reviews

When you need a 45 mm hole through a reinforced concrete wall and a solid drill bit would take forever to grind through that much material, a core bit is the answer. Unlike a...

3.6 out of 5 stars·5 reviews

Some tools are bought for a single project and then gather dust. An oscillating multi-tool tends to be the opposite — once you own one, you find yourself reaching for it...

4.1 out of 5 stars·4 reviews

An oscillating multi-tool is only as good as the blade you put on it. The tool itself provides the motion, but it is the blade that does the actual work — cutting through...